Search results for "Strategy and Management1409 Tourism"
showing 10 items of 32 documents
Experimental and numerical investigation on a new FSW based metal to composite joining technique
2018
Abstract In the last decades, different techniques were proposed to join aluminum sheets with composites materials. Each of them has advantages and weak points over the others and new techniques and patents are continuously developed to overcome these difficulties. In this paper an experimental and numerical investigation on a new Friction Stir Welding based approach to mechanically join AA6082-T6 to self-reinforced polypropylene is presented. The aluminum sheet is pre-holed along both the sides of the weld line and a pinless tool generates the heat and pressure needed to prompt back-extrusion of the composite. New experimental fixtures and hole designs were investigated in order to enhance…
Evaluating the material resource efficiency of secondary aluminium production: A Monte Carlo-based decision-support tool
2019
The contamination of aluminium streams during the different life cycle stages by alloy mixing and/or accumulation of foreign elements, in combination with the limited melt purification options during remelting, represents an important limiting factor in recycling. Consequently, in secondary aluminium production, primary aluminium is used to dilute the concentration of the residual elements, and alloying elements are added to adjust the composition to the target alloy specifications. However, adding elements, for which their refinement in a subsequent recycling step is problematic, results in permanent down-cycling or ‘quality losses’. Hence, it is crucial to more efficiently control the com…
Process mechanics in Friction Stir Extrusion of magnesium alloys chips through experiments and numerical simulation
2017
Abstract Friction Stir Extrusion (FSE) is a novel process designed to directly recycle machining chips. An experimental campaign was carried out on AZ31 milling chips using variations in extrusion ratio, force and tool rotation rate. The process mechanics were studied and correlated to the material flow, which was elucidated through use of a copper marker. A 3D, Lagrangian, thermo-mechanically coupled dedicated numerical model was set up and validated through temperature measurements. The combination of experimental and numerical results permitted to reconstruct the complex 3D material flow induced by tool rotation and plunge into the extrusion billet chamber.
Enhancement of mechanical properties of FSWed AA7075 lap joints through in-situ fabrication of MMC
2017
Abstract Friction Stir Processing (FSP) has been demonstrated feasible to create local Metal Matrix Composites (MMCs) in light alloys matrix. In this research, local MMCs were produced contextually to the weld using Friction Stir Welding (FSW). SiC particles were added to AA7075 lap joints by creating a proper groove on the top surface of the bottom sheet. Different welds were produced with increasing number of tool passes. The effect of the multiple passes was investigated through shear tests, macro and micro observations, average grain size and microhardness measurements. The welded joints were compared to a reference weld produced with no reinforcements. It was found that poor mixing bet…
The magnitude of a product recall: offshore outsourcing vs. captive offshoring effects
2018
The escalation in product recalls in recent years is attributed to the rise of globalisation and associated challenges of offshoring. Extant SCM research suggests that product recalls have a significant negative impact on financial performance, but gaps exist relative to the managerial actions to minimise their impact. Recall response strategies have become more important in the press, given that a single recall may result in the mandatory withdrawal of millions of products from the market, with firms incurring enormous logistics costs and brand damage. In this study, we address this gap in the research, and using a measure of product recall defined as the volume of products withdrawn from …
SUP R DSS: A sustainability-based decision support & system for road pavements
2019
Road pavement community members are increasingly becoming aware of the need to incorporating the principles of sustainable development into the sector. Policies are also going in this direction and as a consequence in the recent years researchers and practitioners are coming up with new materials, technologies and practices designed to reduce the negative impacts of their activities in the surroundings. Within this framework the road pavements sector is witnessing a paradigm shift towards the development of pavement technologies incorporating high-content of recycled materials, as well as best practices to decrease the overall carbon footprint. These are all promising solutions that to the …
Nitrous oxide emission in a University of Cape Town membrane bioreactor: The effect of carbon to nitrogen ratio
2017
Abstract The effect of the carbon-to-nitrogen (C/N) ratio in the influent on the nitrous oxide (N 2 O) emission from a University of Cape Town Membrane BioReactor pilot plant was investigated. The membrane was located in a separate tank to single out the production of N 2 O due to the biological processes from N 2 O stripping as a result of the extra aeration needed for the mitigation of membrane fouling. The experimental campaign was divided into two phases, each characterized by a different C/N ratio (namely, 10 and 5 mgCOD/mgTN, Phase I and Phase II, respectively). The decrease of the C/N ratio promoted the increase of N 2 O emissions in both gaseous and dissolved phases, mainly due to a…
The effect of the solids and hydraulic retention time on moving bed membrane bioreactor performance
2018
Abstract The aim of the present paper was to investigate the effect of solids (SRT) and hydraulic (HRT) retention time on Integrated Fixed Film Activated Sludge (IFAS) University of Cape Town (UCT) membrane Bioreactor (MBR). In particular, three different pairs of SRT and HRT values were analysed, namely, Phase I 56 d/30 h, Phase II 31 d/15 h and Phase III 7 d/13 h. The short-term effect of these three SRT/HRT conditions was assessed by analysing several system performance indicators: organic carbon and biological nutrient (nitrogen and phosphorus) removal, biomass respiratory activity, activated sludge filtration properties and membrane fouling. The results showed that the decrease of SRT/…
Unbundling technology adoption and tfp at the firm level. Do intangibles matter?
2012
We use a panel of European firms to investigate the relationship between intangible assets and productivity. We distinguish between total factor productivity (tfp) and technology adoption, whereas standard estimations consider only a notion of productivity that conflates the two effects. Although we are unable to address simultaneity, we allow for the existence of multiple technologies within sectors through a mixture model approach. We find that intangible assets have nonnegligible effects that both push firms toward better technologies (technology adoption effects) and allow for more efficient exploitation of a given technology (tfp effects).
Competitiveness and sustainability in horticulture: strategy for small businesses
2018
Vegetable cultivation has a significant history in the countries of the Mediterranean basin. Italy is an important horticultural producer and, in this context, Sicily offers ideal conditions for the protected cultivation of field vegetables. Apart from a few well-organised producers, in many areas horticulture is characterised by backward entrepreneurial systems and fragmented production lines that make the vegetable market one that is very close to being a rigged competition in which companies must accept the price and have no negotiating power. This situation has been aggravated even further by the recent economic crisis and the subsequent recession, resulting in the disappearance of the …